I know it has been over 3 months since Hanging Gutter Garden Part 1: Adventures in Home Depot. But I do have excuses. One excuse is that I lost my camera battery charger and I could not take pictures of my progress, another is that I’m lazy. But, just before the backpacking extravaganza (and after losing Reid’s camera in the Canyonlands) I broke down and purchased a new (expensive) charger (with LED charging screen and European outlet adapter).
Now that I have the means to take picture I figured it was about time to share my patio garden with you lovely people.
As I said in this post, I wanted to create the hanging gutter garden like this one.
For mine I didn’t have the fancy pants hardware (or the fancy pants bank account). I used the gutter given to me by the gutter guys (A story told here). I also purchased a plastic gutter for $5 at Resource 2000, where they sell salvaged construction materials.
- 1 gutter cut into three equal parts (process is almost identical no matter the material, I tried with both plastic and metal gutters)
- 6 gutter caps – the plastic ones are quite nice and can be purchased at Home Depot, Metal are also nice but mine had to be bent to fit the gutter, which was quite a process.
- 2 hooks – I chose some that screw into a drilled hole
- 16’ of 1/8” steel cable cut into 6 equal lengths (or as much as you’ll need to fill your space, gutters should be at least 18” apart to allow adequate sun exposure and plant growth) – I bought this kit at walmart because I was there buying pots and it was the only cable they had. The kit actually came in handy as the clips (though not exactly what I was looking for) worked perfectly. As I worked I realized I needed 32” of cable for both my gutter gardens so I ended up having to go to Home Depot for a yard of steel cable.
- 12 clips – 6 came in the kit mentioned above and there was another pack nearby without 3 clips (no cable) so I bought two of these packs.
- 2 thimbles – these came in the kit mentioned above but they are also sold alone
- Wire Cutters – sharpened
- Electric drill – with attachments for drilling holes large enough for the steel wire to go through and for tightening nuts on the clips
Step 1. Cut the gutters
The gutter man who gave it to me cut the metal gutter in uneven thirds; my dad then cut into equal length pieces. I sawed the plastic gutter into (almost) equal thirds (I did it all by myself thank you).
Step 2. Drill holes
My dad helped me drill two holes, large enough for the steel cable to fit through, across from each other on each end, and one hole at the center of the base on each end (6 holes per gutter section).
Step 3. Fit the end caps
This part was quite complicated for the metal gutter. The plastic gutter was simple, the caps fit perfectly. My Metal Gutter was not the exact shape of the cap. My dad used pliers to shape the end of the gutter to fit into the cap and a rubber mallet to force it in where it wasn’t exactly perfect. He did this for each of the 6 end caps and I am so grateful for that. If you buy your gutter where you buy your end cap this shouldn’t be a problem for you, mine came from different sources.
Step 4. Cut steel cable into 6 36” sections
We definitely over estimated the amount of steel cable to use. My dad and I were not at my apartment during the building process so we wanted to give ourselves some extra. You might not need so much extra slack when building your gutter garden. Be careful when cutting the wire, it tend to fray; very sharp wire cutters can help prevent fraying.
Step 5. Thread the steel cable
With one end shorter than the other thread the cable through the two holes at the top of the gutter. This can be quite difficult if the cable has frayed. Also be prepared to be poked with sharp metal; gloves are probably a good idea at this point.
Step 6. Secure the cable
Loosen the nuts on the clip and thread both ends of the cable through the clip. Pull the clip down on the cable where its not pulling to much but is tight. Finagle the cable so the short end only pokes out of the clip about an inch and tighten the nuts on the clip, a little on each nut so it tightens evenly. Repeat this process (step 5 and 6) for each gutter on each end (a total of 6 times)
Step 7. Connect the pieces
Starting with the gutter section you want at the base of your garden thread the long end of the cable through the hole in the base of the middle gutter section. Attach a clip around this single end of cable and tighten. Make sure the clip is at the length you want. Do this on both ends, keeping the gutter level. Do the same thing with the middle gutter and the top gutter. Leave the top gutter for now.
Step 8. Hanging the dang thing
This was another complicated step. The whole contraption is very heavy, awkward and dynamic. This stage was obviously done at my apartment with my boyfriends help to replace my dad. There is most definitely a better way than how we did this but I am the queen of doing things in the most complicated way. We measured the distance between cables, drilled holes for the screw hook and screwed them in. Then we hauled the apparatus up a step stool and one of our kitchen chairs between the two of us. I stabilized my end as he threaded a clip onto the cable then a thimble around the hook and tightened it. We kept the thing slightly above the railing so that when we screwed it down it would be tight. Mind you this took many, many, many, many, MANY tries because there were so many pieces to hold steady at a precise place, but we finally got it and 3 months later it looks fantastic.
Side note: The method above details how we hung the metal gutters. For the plastic gutters we screwed the bottom gutter onto the railing first, but we couldn’t get it tight enough at the top and it looks like it’s leaning forward since the hooks at the top and the screws at the base are not directly vertical. Therefore we developed the method above, which was also difficult but returned better results.
These gutters dry out VERY fast, especially in an arid climate like Colorado. I have struggled with wilting, browning, and flat out dying plants in these gutters since planting. I have discovered that on hot days I must water them twice: once in the morning and once in the evening, in order to keep them healthy. Someone in a more humid environment might not experience these problems.
How did you like this post? Are you interested in making a gutter garden? Do you have questions about my process? Leave a comment.